9 Common Problems with Pigment Materials and Solutions
Colour masterbatches are a new type of colouring agent for polymer materials. Thanks to their superior colouring performance, energy efficiency, dust-free operation and lack of pollution, they are widely used for colouring plastics, building profiles and agricultural pipes. However, certain issues may arise during the use of colour masterbatches; let us now take a closer look at the causes and solutions:
1. When exposed to sunlight, streaks of pigment appear in the finished product
This issue needs to be considered from two perspectives: the physical and mechanical properties of plastics, and plastic moulding processes:
1. The temperature of the injection moulding equipment was not properly controlled, meaning that the colour masterbatch could not mix thoroughly with the resin after entering the mixing chamber.
2. As the injection moulding machine was not operating with sufficient back pressure, the mixing efficiency of the screw was poor.
3. Poor dispersion of the colour masterbatch or inadequate plasticisation of the resin.
The following adjustments can be made to the process:
1. Slightly increase the temperature in the part of the mixing chamber near the discharge port
2. Apply a certain amount of back pressure to the injection moulding machine.
If the problem persists after carrying out the above troubleshooting steps, it may be due to issues with the dispersibility or compatibility of the colour masterbatch or resin; you should contact the colour masterbatch manufacturer to resolve the issue. Reply with “colour” to view more articles.
II. After using a particular colour masterbatch, the finished products appear to be more prone to breaking
This may be due to poor diffusion and miscibility resulting from the use of low-quality dispersants or additives by the manufacturer, which affects the physical and mechanical properties of the finished product.
3. The colour is too dark (or too light) after using the colour masterbatch in accordance with the instructions on the packaging
Although this question is simple, there are many possible answers, namely:
1. The colour masterbatch has not been thoroughly colour-tested; there is either too little or too much pigment.
2. Inaccurate measurement during use; there is widespread practice of arbitrary measurement among domestic enterprises, particularly small and medium-sized enterprises.
3. There are issues with the compatibility between the colour masterbatch and the resin; this may be due to an inappropriate choice of carrier for the colour masterbatch, or the manufacturer arbitrarily changing the resin grade.
4. Incorrect machine temperature, resulting in the colour masterbatch remaining in the machine for too long
Procedure: Firstly, check that the resin type is compatible with the colour masterbatch and that the dosage is accurate; secondly, adjust the machine temperature or rotational speed. If the problem persists, contact the colour masterbatch manufacturer.
IV. Why do products moulded using the same colour masterbatch, resin and formulation exhibit variations in colour intensity when produced on different injection moulding machines?
This is often caused by the injection moulding machine. Differences in the mechanical condition of injection moulding machines—depending on their manufacture, age or maintenance—can lead to variations, particularly in the degree to which the heating elements contact the barrel. This, in turn, affects how the colour masterbatch is dispersed within the barrel, resulting in the aforementioned phenomenon. Reply with “injection moulding machine” to view more articles.
5. Why did the colour change when I switched to a different brand of resin, even though I used the same colour masterbatch and formulation?
Different grades of resin vary in density and melt index; consequently, their properties differ, as does their compatibility with colour masterbatches, which can lead to colour variations. Generally speaking, provided that the differences in density and melt index are not significant, the colour differences will not be too pronounced, and the colour can be corrected by adjusting the amount of colour masterbatch used.
VI. Does pigment migration occurring in colour masterbatches during storage affect the quality of the finished products?
Some colour masterbatches have a very high pigment (or dye) content; in such cases, migration is to be expected. In particular, colour masterbatches containing dyes are prone to significant migration. However, this does not affect the quality of the finished product, as once the colour masterbatch has been injection-moulded into the product, the pigment is present at a normal colouring concentration within the product.
VII. Why do some injectable products have a poor sheen?
There are several possibilities, as follows:
1. The nozzle temperature of the injection moulding machine is too low
2. The mould surface finish on the injection moulding machine is poor
3. Excessively long moulding cycle times
4. Excessive titanium dioxide content in the colour masterbatch
5. Poor dispersion of the colour masterbatch
VIII. After a period of time, some plastic products may fade.
The basic pigments used by the manufacturer were of poor quality, resulting in colour drift.
IX. Why are colour variations particularly common in ABS colour concentrates?
There can be significant colour variations between different grades of ABS produced in various countries; even within the same grade of ABS, such variations may occur between batches. However, these colour variations are generally not significant. Users should bear this characteristic of ABS in mind when using ABS colour masterbatches.
Follow the WeChat official account