What issues should be taken into account when using plastic pipes? How should one select high-quality Sumlong colour masterbatches specifically designed for pipes?

Chemical building materials, having emerged as another important building material following steel, timber and cement, have already demonstrated remarkable vitality and broad prospects for development within China’s modern construction industry. Plastic pipes, as a key component of chemical building materials, have been widely accepted by users for their superior performance, hygiene, environmental friendliness and low energy consumption, and are extensively used in construction projects. However, as plastic pipes have a relatively short history of development in China, they have only gradually gained prominence in recent years. Whilst people are familiar with traditional cast-iron pipes, their knowledge of plastic pipes remains limited; once accepted, they are often regarded as capable of anything. To help people better understand the properties and applications of plastic pipes, this article outlines several points to bear in mind when using various types of plastic piping.
I. UPVC drainage pipes
UPVC drainage pipes account for approximately 50 per cent of output in China’s plastic pipe industry; they are the most widely used, longest-established and best-known type of plastic pipe in the country. However, during testing, we have found that it is precisely UPVC drainage pipes that present numerous issues. This is because PVC resin has poor performance characteristics, a narrow processing window and extremely demanding moulding conditions. Consequently, for UPVC pipe manufacturers, identifying the optimal additives (such as stabilisers, modifiers, lubricants and fillers), and researching the best formulations and appropriate processes, is a prerequisite for ensuring pipe quality. We shall now outline several common issues.
1. Poor impact resistance. Based on impact tests conducted in accordance with the GB/T 5836.1–92 standard, testing over many years has revealed that the first-pass rate is less than 50 per cent; many products even fracture completely after just 10 impacts.
2. Poor tensile strength and toughness. High-quality UPVC pipes should exhibit a tensile strength curve with a distinct yield point and high elongation, as shown in Figure 1, whilst inferior pipes are often brittle, with low elongation and a tendency to fracture. 3. Low softening temperature, making them prone to deformation when exposed to heat. In terms of test performance, this manifests as a low Vicat softening temperature (less than 79). Some manufacturers, in an attempt to raise the softening temperature, simply increase the amount of filler during compounding. Whilst this does indeed raise the softening temperature, it significantly reduces the pipe’s other properties, particularly impact resistance, tensile strength and toughness. Therefore, to raise the softening temperature without compromising—or only minimally compromising—other properties, careful attention must be paid to the selection of additives, the ratio of raw materials, the production process and the manufacturing machinery; this matter must not be treated lightly.

II. UPVC Water Supply Pipes
UPVC water supply pipes are tested in accordance with the national standard GB/T 10002.1-1996, which sets high standards for hydraulic testing performance; this places significant demands on manufacturers of UPVC water supply pipes. The issue of pipe eccentricity, which is perhaps not given sufficient attention, can lead to significant variations in wall thickness in the manufactured pipes. This not only results in a waste of raw materials but also makes it difficult for the pipes to meet the ring stress requirement of 42 MPa in hydraulic testing. Consequently, manufacturers must not only ensure the correct material proportions but, where feasible, install in-line inspection equipment to adjust dimensional deviations in the pipes as and when necessary.

III. Aluminium-plastic composite pipes
There are currently three types of aluminium-plastic composite pipes available on the market: PE/AL/PE; PE/AL/XPE; and XPE/AL/XPE. The first type has polyethylene inner and outer layers; the second type has a cross-linked polyethylene inner layer and a polyethylene outer layer; and the third type has cross-linked polyethylene inner and outer layers, with an aluminium layer in the middle. The first type is generally used for cold water pipework systems, whilst the latter two are generally used for hot water pipes. As these pipes contain an aluminium layer, they offer increased resistance to internal pressure, act as a barrier against oxygen and CO₂ to prevent corrosion of water supply equipment, provide good thermal conductivity to reduce the concentration of hot spots, and possess anti-static properties, effective shielding and a degree of flame retardancy; consequently, they are widely accepted by the public. Furthermore, as the connecting fittings are made of copper or stainless steel with threaded seals, installation is relatively straightforward and requires no special tools; the connection method is similar to that of the cast iron pipes currently in widespread use, thereby demonstrating certain advantages.
Whilst this type of pipe causes few problems in cold-water pipework systems, it presents a number of issues when used in hot-water pipework systems, the main ones being as follows:
1. The welded joints in the aluminium layer are a weak point, particularly in the case of lap welds on aluminium-plastic pipes; consequently, most failures during hydraulic testing occur near the weld line. This point warrants particular attention. Consequently, manufacturers should select high-quality welding machines during the production process, strive to maximise the strength of the welds, minimise the formation of sharp protrusions at the edges of the aluminium-layer welds, and avoid the build-up of harmful concentrated stresses.

2. The bond strength between the aluminium layer and the plastic layer—particularly the cross-linked polyethylene layer—is relatively weak, making aluminium-plastic composite pipes prone to delamination and failure when used in hot water pipework systems. This is primarily due to the following reasons: firstly, in order to reduce costs, manufacturers select lower-quality hot-melt adhesives; secondly, the use of paraffin wax as a lubricant during the aluminium pipe forming process to reduce traction resistance, which consequently compromises the adhesive strength; and thirdly, in the case of cross-linked aluminium-plastic composite pipes, the inert nature of cross-linked polyethylene leads to reduced adhesive strength.

3. In the case of cross-linked aluminium-plastic composite pipes, as some manufacturers do not carry out the hydrolysis cross-linking or autoclave cross-linking process thoroughly enough, the degree of cross-linking in the cross-linked polyethylene layer is low (less than 65 per cent). This reduces the pipe’s high-temperature hydrostatic strength, thereby significantly increasing the risk associated with its use in hot water pipework systems.

4. In the case of cross-linked aluminium-plastic composite pipes, some manufacturers, in order to reduce costs, deliberately reduce the thickness of the cross-linked polyethylene layer during production whilst increasing the thickness of the non-cross-linked layer, thereby reducing the high-temperature hydrostatic strength of the entire pipe.
5. Aluminium-plastic composite pipes with both inner and outer layers cross-linked are best suited for use in hot water pipework systems. However, at present, many manufacturers are making extensive use of aluminium-plastic pipes with only the inner layer cross-linked for hot water pipework; it is important to note that this practice carries numerous potential risks. During testing, we found that when the latter type of aluminium-plastic composite pipe is used in hot water systems (particularly where water temperatures exceed 90°C), the significant temperature difference between the inner and outer layers may cause the plastic layers to expand and contract at different rates, leading to leaks at the joints or brittle fracture. 6. It should also be noted that some domestic manufacturers have begun using DowLEX 2344E LLDPE, a polyethylene resin produced by Dow Chemical Company in the USA, to manufacture non-cross-linked, high-temperature-resistant aluminium-plastic composite pipes. whose high-temperature static hydraulic strength is also relatively satisfactory; however, as it is more expensive and does not belong to the same category as cross-linked aluminium-plastic composite pipes, it requires separate consideration.

IV. Polyethylene (PE) Water Supply Pipes
Internationally, research into and improvements of polyethylene materials for use in pipework have been ongoing. It is precisely due to these continuous improvements in material performance—particularly the advent of PE100 pipes—that the allowable stress of polyethylene pipes has been significantly increased. This allows for reduced wall thickness and an increased flow cross-section whilst maintaining the same operating pressure, whilst simultaneously enhancing resistance to crack propagation, further enhancing the advantages of polyethylene pipes. Currently, polyethylene pipe materials are classified internationally into five grades: PE32, PE40, PE63, PE80 and PE100, with PE80 and PE100 being the primary materials used for gas and water supply pipes. In China, there is no grading system for specialised polyethylene pipe materials, which makes it difficult for domestic manufacturers of polyethylene gas and water supply pipes to select raw materials, and also poses significant potential risks to the use of polyethylene pipes. Consequently, the National Standards Administration has made extensive revisions to the new GB/T 13663-2000 standard, stipulating that different grades of PE80 and PE100 for water supply pipes correspond to different pressure strengths. Furthermore, the tensile strength requirement from the old standard has been removed, whilst an elongation at break (greater than 350 per cent) has been added, thereby emphasising fundamental toughness.

So, what is the current situation regarding PE pipes in China? We have identified a number of issues during our inspections.

1. Many domestic manufacturers produce PE pipes with high tensile strength but a pitifully low elongation at break—ranging from just 40 per cent to 80 per cent. Consequently, these pipes are relatively rigid and lack ductility, which significantly reduces their seismic resistance, increases the difficulty of installation, and poses considerable challenges for fusion welding.
2. Poor pigment dispersion. During testing, we found that PE pipes with good pigment dispersion exhibited an elongation at break of up to 700 per cent, whilst those with poor dispersion sometimes had an elongation at break of only around 100 per cent. Consequently, pigment dispersion also has a significant impact on the physical and mechanical properties of the pipes.